Methods of Manufacturing Pipe Fittings

Aug 9, 2020 · 5 min read

Pipe Fittings Manufacturing Process

Introduction

Pipe fittings are piping component that helps in changing the direction of the flow such as elbows, tees; changes the size of the pipe such as reducers, reducing tees; connect different components such as couplings and stop the flows such as caps, fittings.

Pipe fittings are manufactured from stainless steel seamless pipes, carbon steel seamless pipes and from welded pipe with filler material. Large diameter fittings are manufactured from plate.

Various methods used for manufacturing pipe fittings are shown in the below diagram: -

Butt-Welding Manufacturing Processes

1. Elbow Manufacturing Process

a. Mandrel Method/Hot Forming Method

· One of the most common manufacturing methods for manufacturing elbows from pipes.

· After heating the raw material, it is pushed over a die called “mandrel” which allows the pipe to expand and bend simultaneously. Applicable to a wide size range.

· Characteristics of mandrel bending strongly depend on the integrated shape and dimensions of the mandrel.

· Elbows manufactured by using hot mandrel bending have advantages of small thickness deviation and shorter bending radius than those of any other bending method type.

b. Extrusion Method/Cold Forming Method

· In the cold extrusion method, a pipe with the same diameter as a finished product is pushed through a die and formed into its desired shape. Usually applied to stainless steel small to medium sizes elbows.

c. “UO” Method (Welding)

·In this method the plate is cut out into a specially designed shape, it is formed first into a U-shape using a die and then into an O-shape or tubular form using another die, that is why this method is known as UO method. Once the fittings formed in tumbler shaped it is welded from inside and outside of the closing seam. A cut plate is 1st from in U shape and then in O shape

d. Hot Forming Die Bending Method

·In this method the pipe is been inspected before any process. Then after cutting out pipe into specified length, it goes under elliptical forming using a die shown in the picture. For producing a specified radius for elbow, it bends in another die. In the next step the elbow goes under heat treatment. In the end shot blasting, cleaning, bevelling and coating are done respectively to finalize the product.

2. Tee Manufacturing Process

a. Hydraulic Bulge Method (Cold Forming)

·Cut piece of Pipe is placed in hydraulic die and liquid is fill inside the pipe, Hydraulic pressure pushes out the branch, in the fixed opening in the die.

· This method gives the good surface finish. However, higher thickness Tee cannot be manufactured by this method.

b.“Monaka” Method

· This manufacturing method is similar to Elbows, using steel plates as the raw material.

· In this method two pieces of raw material plates cut out symmetrically and are press-formed and welded together.

c. Hot Extrusion Method

· Tee with large diameters, heavy wall thickness and/or special material with challenging workability that cannot be manufactured using the hydraulic bulge method are manufactured using hot Extrusion Method.

· In Hot Extrusion Method, normally bigger diameter pipe is used than the finished product size; the branch outlet is extruded from the pipe with help of extrusion tool.

· Other dimensions of body and branch can also be adjusted by pressing the die if required.

3. Reducer Manufacturing Process

a. Outer Die Method

·One of the most common method for manufacturing Reducers is using an outer die.

· The pipe is cut and pressed in the outer die; compressing the one end of the pipe into a smaller size. This method is useful for manufacturing of small to medium size of reducers.

b. Plate Forming Method

·Plates can also be used to manufacture Reducers.

· In an UO method, plate is cut in a specially designed shape which is formed into a U-shape and an O-shape respectively, then finished with a single weld seam.

4. Cap Manufacturing Process

a. Deep Drawing Method

·CAPs are manufactured by Deep Drawing method. In this method, Plate is cut out in a circle and formed by deep drawing die.

5. Stub End Manufacturing Process

a. Flaring Method

· Stub Ends or Lap Joints Flange are manufactured by flaring method. Pipe end is a flare or spared out to form flange face. Stub ends are also manufactured by forging in which forge block are machined to final dimension.

Forged Fittings Manufacturing Processes

1. Open-Die Forging

Open die forging is the process of deforming a piece of metal between multiple dies that do not completely enclose the material. The metal is altered as the dies “hammer” or “stamp” the material through a series of movements until the desired shape is achieved. Products formed through open forging often need secondary machining and refining to achieve the tolerances required for the finished specifications. Open die forging is often used for short run forgings of parts that are simple, rather than complex, in design, such as discs, rings, sleeves, cylinders and shafts. Custom shapes can also be produced with open die forging. The repeated working of the material through the deformation process increases the strength of the grain structure. Some additional benefits of open die forging include improved fatigue resistance and strength.

2. Closed-Die Forging

Closed die forging (also referred to as impression die forging) is a metal deformation process that uses pressure to compress a piece of metal to fill an enclosed die impression. In some closed die forging processes, a succession of impression dies is used to modify the shape of the material into the final desired shape and form. The type of material, tightness of tolerances, and need for heat treatment can determine the number of passes the product requires through the dies.

Types of Pipe Fittings

At Metallica, we are manufacturing a wide range of pipe fittings, for which we use seamless pipes and welded pipes as a key raw material. In addition to being a pipe fittings manufacturer, we are also one of the biggest seamless pipe manufacturer and supplier, enabling us to offer cost advantages to our customers.

Fittings are divided into the following 4 groups:

Metallica is a specialist manufacturer and supplier of steel pipes and various types of pipe fittings in India such as butt-welding pipe fittings (both weld and no weld), socket welding and threaded pipe fittings, and flanged pipe fittings. We are a professional manufacturer of carbon steel, stainless steel, and alloy steel seamless butt-welding pipe fittings, forged fittings and flanges. We have the CE PED & ISO etc. certificates.

If you are interested in purchasing high quality pipe fittings, please contact us now for prices and product details. Email Us on info@metallicametals.com | Call Us On +918928722715

Medium is an open platform where 170 million readers come to find insightful and dynamic thinking. Here, expert and undiscovered voices alike dive into the heart of any topic and bring new ideas to the surface. Learn more

Follow the writers, publications, and topics that matter to you, and you’ll see them on your homepage and in your inbox. Explore

If you have a story to tell, knowledge to share, or a perspective to offer — welcome home. It’s easy and free to post your thinking on any topic. Write on Medium

Get the Medium app